RIFF JTAG – Easy repair Samsung SGH-T699 Galaxy S Relay 4G / Blaze Q supported

RIFF JTAG – Easy repair Samsung SGH-T699 Galaxy S Relay 4G / Blaze Q supported

Repairing bricked Samsung T699 is easy with the RIFF Box.
There is some kind of anti-downgrade protection implemented in this model. Thus You have to resurrect your phone with the firmware version not lower than the one the phone had before being killed. For this, during resurrection You can select firmware version to be used as resurrection data.
In case there is even more newer firmware available which is not yet included into current DLL, You can always use eMMC Plugin to manually flash boot partitions into your phone. For this, click plugin’s the ‘Load Layout from Device’ button and then use ‘Inject Data from File…’ mouse righ clicks to inject boot files from firmware You have into the proper partitions (SBL1, SBL2, SBL3, RPM, TZ and ABOOT) and then flash them back to phone.

To resurrect Samsung T699:

  •  Solder JTAG cable to Samsung T699 JTAG pads;
  •  Connect USB cable or instert batteryu;
  •  Make sure Samsung T699 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, You can flash it using known flashing methods.
.
samsung_galaxy_s_relay_4g

RIFF JTAG – Easy repair Orange Nivo 7560U supported

RIFF JTAG – Easy repair Orange Nivo 7560U supported

Resurrecting the Orange Nivo 7560U is easy.

To resurrect the Orange Nivo 7560U:

  •  Solder JTAG cable to Orange Nivo 7560U JTAG pads;
  •  Solder the Power Button to ground;
  •  Connect power supply 4.2V to the battery connectors;
  •  Make sure Orange Nivo 7560U is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.
orange_nivo

RIFF JTAG – Easy repair Huawei Ascend Y300-0100 U8833 (Huawei Asura) supported

RIFF JTAG – Easy repair Huawei Ascend Y300-0100 U8833 (Huawei Asura) supported

Repairing bricked Huawei Y300 is easy with the RIFF Box.

To resurrect Huawei Y300:

  •  Solder JTAG cable to Huawei Y300 JTAG pads;
  •  Connect Huawei Y300 tablet’s charger for power;
  •  Make sure Huawei Y300 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Now device is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.
huawei_y300_0100

RIFF JTAG – Easy repair Huawei UML397 4G LTE™ Wireless Modem supported

RIFF JTAG – Easy repair Huawei UML397 4G LTE™ Wireless Modem supported

Repairing bricked Huawei UML397 is easy with the RIFF Box

To resurrect Huawei UML397:

  •  Solder JTAG cable to Huawei UML397 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Huawei UML397 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now device is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.
UML397US-Front-Image

RIFF JTAG – Easy repair HTC Desire 500 506e (HTC Z4) supported

RIFF JTAG – Easy repair HTC Desire 500 506e (HTC Z4) supported

Repairing bricked HTC Desire 500 (0P3Z10000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘0P3Z10000’.

To resurrect HTC Desire 500 (0P3Z10000):

  •  Solder JTAG cable to HTC Desire 500 (0P3Z10000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire 500 (0P3Z10000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_500

RIFF JTAG – Easy repair HTC Desire 600 (HTC CP3) supported

RIFF JTAG – Easy repair HTC Desire 600 (HTC CP3) supported

Repairing bricked HTC Desire 600 (PO4911000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PO4911000’.

To resurrect HTC Desire 600 (PO4911000):

  •  Solder JTAG cable to HTC Desire 600 (PO4911000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire 600 (PO4911000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_600

RIFF JTAG – Easy repair HTC Butterfly S 901s 4G LTE supported

RIFF JTAG – Easy repair HTC Butterfly S 901s 4G LTE supported

Repairing bricked HTC Butterfly S (PO6821000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.54.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PO6821000’.

To resurrect HTC Butterfly S (PO6821000):

  •  Solder JTAG cable to HTC Butterfly S (PO6821000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Butterfly S (PO6821000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
HTC-Butterfly-S-901e-16GB-3G-(Unlocked)-Mobile-Phones-Red-3-360x360