RIFF JTAG – Easy repair HTC One mini LTE 601n (HTC M4) supported

Repairing bricked HTC OneMini (PO5820000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.19.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PO5820000’.

To resurrect HTC OneS:

•  Solder JTAG cable to HTC OneMini (PO5820000) JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure HTC OneMini (PO5820000) is selected in the list of models;
•  If you use battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Easy repair Lenovo/Acer Gobi 2000 modem card supported

Resurrecting Qualcomm ThinkPad GOVI2000 is simple.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0020/0x8829.

To resurrect Qualcomm ThinkPad GOVI2000:

•  Solder JTAG cable to Qualcomm ThinkPad GOBI2000 JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure Qualcomm ThinkPad GOVI2000 is selected in the list of models;
•  Click Resurrect button;
•  Choose which areas to flash;
•  Wait till software signals a successful operation completion;
•  De-solder JTAG wires;

You can select Acer or Lenovo firmware version.

..

RIFF JTAG – Easy repair CDMA ZTE C132 Striker supported

Resurrecting ZTE C132 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0x0063.

To resurrect ZTE C132:

•  Solder JTAG cable to ZTE C132 JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure ZTE C132 is selected in the list of models;
•  Click Resurrect button;
•  Choose which areas to flash;
•  Wait till software signals a successful operation completion;
•  De-solder JTAG wires;

.

RIFF JTAG – Easy repair CDMA ZTE S183 supported

Resurrecting ZTE S183 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0x0063.

To resurrect ZTE S183:

•  Solder JTAG cable to ZTE S183 JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure ZTE S183 is selected in the list of models;
•  Click Resurrect button;
•  Choose which areas to flash;
•  Wait till software signals a successful operation completion;
•  De-solder JTAG wires;

.

RIFF JTAG – Easy repair CDMA Alcatel C131 supported

Resurrecting Alcatel C131 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0x0063.

To resurrect Alcatel C131:

•  Solder JTAG cable to Alcatel C131 JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure Alcatel C131 is selected in the list of models;
•  Click Resurrect button;
•  Choose which areas to flash;
•  Wait till software signals a successful operation completion;
•  De-solder JTAG wires;

.

RIFF JTAG – Easy repair HTC Desire VC (XC) T329d supported

Repairing bricked HTC DesireVC (PK7820000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.00.0004 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PK7820000’.

To resurrect HTC DesireVC (XC) t329D (PK7820000):

•  Solder JTAG cable to HTC DesireVC (PK7820000) JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure HTC DesireVC (PK7820000) is selected in the list of models;
•  If you use battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Easy repair Lenovo A760 supported

Repairing bricked Lenovo A760 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Lenovo A760:

•  Solder JTAG cable to Lenovo A760 JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure Lenovo A760 is selected in the list of models;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.

RIFF JTAG – Easy repair Philips Xenium W737 supported

Repairing bricked Philips W737 is easy with the RIFF Box.

To resurrect Philips W737:

•  Solder JTAG cable to Philips W737 JTAG pads;
•  Connect Philips W737 tablet’s charger for power;
•  Make sure Philips W737 is selected in the list of models;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  De-solder JTAG wires;

Now device is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.

RIFF JTAG – Easy repair Samsung GT-S7560M Galaxy Ace II X supported

Repairing bricked Samsung S7560M is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7560M:

•  Solder JTAG cable to Samsung S7560M JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure Samsung S7560M is selected in the list of models;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Easy repair Samsung SGH-T989D Galaxy S II X (Samsung Hercules) supported

Repairing bricked Samsung T989D is easy with the RIFF Box. The device is based on the Qualcomm APQ8060 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung T989D:

•  Solder JTAG cable to Samsung T989D JTAG pads;
•  Connect USB cable to phone and PC;
•  Insert battery;
•  Make sure Samsung T989D is selected in the list of models;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press Power-On.

.