RIFF JTAG – HTC Titan X310E (HTC Eternity) Unbrick, Unlock, IMEI and SuperCID repair supported

19.04.2013  RIFF JTAG – HTC Titan X310E (HTC Eternity) Unbrick, Unlock, IMEI and SuperCID repair supported

Repairing bricked HTC Titan (PI3911000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC Titan (PI3911000) boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM chip). In this case the JTAG may be enabled only by firmware itself. This is done by the DBL loader, so if DBL area is damanged and MCU has JTAG Disable FUSE blown then there is no way to resurrect your phone via JTAG interface. However, in this case you may use HTC Titan (PI3911000) USB DLL version which does not require JTAG interface and does resurrection procedure via USB cable.
Resurrector will reflash radio’s boot zone (except DBL area) and will re-write PDA’s SPL. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PI3911000’.

To resurrect HTC Titan (PI3911000):

  •  Solder JTAG cable to HTC Titan (PI3911000) JTAG pads;
  •  Insert battery and connect USB Data cable;
  •  Make sure HTC Titan (PI3911000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_titan_x310

RIFF JTAG – HTC Flyer 4G P515E Unbrick, IMEI, SuperCID, ModelID repair supported

02.11.2012   RIFF JTAG – HTC Flyer 4G P515E Unbrick, IMEI, SuperCID, ModelID repair supported

Repairing bricked HTC Flyer4G (PG4130000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC Flyer4G (PG4130000) boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM chip). In this case the JTAG may be enabled only by firmware itself. This is done by the DBL loader, so if DBL area is damanged and MCU has JTAG Disable FUSE blown then there is no way to resurrect your phone via JTAG interface. However, in this case you may use HTC Flyer4G (PG4130000) USB DLL version which does not require JTAG interface and does resurrection procedure via USB cable.
Resurrector will reflash radio’s boot zone (except DBL area) and will re-write PDA’s SPL to 1.14.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG413****’.

To resurrect HTC Flyer:

  •  Solder JTAG cable to HTC Flyer JTAG pads;
  •  Insert battery and connect USB Data cable;
  •  Make sure HTC Flyer4G (PG4130000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods. You can use CWM recovery to flash any ZIP file – for this during resurrection add BOOT & RECOVERY zones to be resurrected too.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Flyer WiFi (PG41400) Unbrick, S-off, CID update supported

RIFF JTAG – HTC Flyer WiFi (PG41400) Unbrick, S-off, CID update supported

Repairing bricked HTC Flyer WiFi (PG41400) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC Flyer boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the DBL loader, so writing to DBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into DBL zone and will respond with success code as if flashing succeeded. In this way DBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except DBL area) and will re-write PDA’s SPL to 1.11.0011 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG4140000’.
There is option to reflash android BOOT and RECOVERY zones. Recovery zone is flashed with ClockworkMod Recovery 4.0.1.4. In addition, you can set S-OFF (unlock HBOOT so you will be able to flash any ROM) by selecting S-OFF HBOOT version in the resurrector settings.
Sometimes (for example after rooting attempts) phone has a modified DBL loader (which may not accept official HTC boot files). To restore phone functionality you need to reflash DBL loader. There is option to reflash DBL code (DBL area will be temporary unlocked for reflashing). But please note, reflashing DBL area is very dangerous, since in case flashing stops in the middle, you will have briked phone with permanently disabled JTAG interface.
Please note, if your phone has the DBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Flyer WiFi:

  •  Solder JTAG cable to HTC Flyer JTAG pads;
  •  Insert battery and connect USB Data cable;
  •  Make sure HTC Flyer (PG41400) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;


Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods. You can use CWM recovery to flash any ZIP file – for this during resurrection add BOOT & RECOVERY zones to be resurrected too.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Flyer (PG41100) Unbrick, Unlock, IMEI, S-off, update supported

06.04.2012  RIFF JTAG – HTC Flyer (PG41100) Unbrick, Unlock, IMEI, S-off, update supported

Repairing bricked HTC Flyer (PG41100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC Flyer boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the DBL loader, so writing to DBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into DBL zone and will respond with success code as if flashing succeeded. In this way DBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except DBL area) and will re-write PDA’s SPL to 1.11.0003 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG4110000’.
There is option to reflash android BOOT and RECOVERY zones. Recovery zone is flashed with ClockworkMod Recovery 4.0.1.4. In addition, you can set S-OFF (unlock HBOOT so you will be able to flash any ROM) by clicking “Make S-OFF” checkbox in the resurrector settings.
Sometimes (for example after rooting attempts) phone has a modified DBL loader (which may not accept official HTC boot files). To restore phone functionality you need to reflash DBL loader. There is option to reflash DBL code (DBL area will be temporary unlocked for reflashing). But please note, reflashing DBL area is very dangerous, since in case flashing stops in the middle, you will have briked phone with permanently disabled JTAG interface.
Please note, if your phone has the DBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Flyer:

  •  Solder JTAG cable to HTC Flyer JTAG pads;
  •  Insert battery and connect USB Data cable;
  •  Make sure HTC Flyer is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods. You can use CWM recovery to flash any ZIP file – for this during resurrection add BOOT & RECOVERY zones to be resurrected too.
.