RIFF JTAG – HTC Desire SV T326e (HTC Magni) Unbrick – Dead boot repair supported

27.05.2013  RIFF JTAG – HTC Desire SV T326e (HTC Magni) Unbrick – Dead boot repair supported

Repairing bricked HTC Desire SV (PM8610000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.35.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PM8610000’.

To resurrect HTC Desire SV (PM8610000):

  •  Solder JTAG cable to HTC Desire SV (PM8610000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire SV (PM8610000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_sv_3

RIFF JTAG – HTC Desire VC T328d Unbrick – dead boot repair supported

09.05.2013  RIFF JTAG – HTC Desire VC T328d Unbrick – dead boot repair supported

Repairing bricked HTC DesireVC (PK7810000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.27.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PK7810000’.

To resurrect HTC DesireVC (PK7810000):

  •  Solder JTAG cable to HTC DesireVC (PK7810000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC DesireVC (PK7810000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_vc_t328d_2

RIFF JTAG – HTC Desire C NFC A320e (HTC Golf) Unbrick, Unlock, SuperCID, IMEI repair supported

20.02.2013 RIFF JTAG – HTC Desire C NFC A320e (HTC Golf) Unbrick, Unlock, SuperCID, IMEI repair supported

Repairing bricked HTC Desire C (PL0110000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.25.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PL0110000’.

To resurrect HTC Desire C (PL0110000):

  •  Solder JTAG cable to HTC Desire C (PL0110000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire C (PL0110000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_c

RIFF JTAG – HTC Desire X (HTC Proto) Unbrick , Unlock, SuperCID and IMEI repair supported

14.02.2013    RIFF JTAG – HTC Desire X (HTC Proto) Unbrick , Unlock, SuperCID and IMEI repair supported

Repairing bricked HTC Desire X (PM6610000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.24.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PM6610000’.

To resurrect HTC Desire X (PM6610000):

  •  Solder JTAG cable to HTC Desire X (PM6610000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire X (PM6610000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_x_2

RIFF JTAG – HTC Desire V T328w (HTC Wind) Unbrick, IMEI, SuperCID, Boot repair supported

15.01.2013 RIFF JTAG – HTC Desire V T328w (HTC Wind) Unbrick, IMEI, SuperCID, Boot repair supported

Repairing bricked HTC DesireV (PL1110000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.14.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PL1110000’.

To resurrect HTC DesireV (PL1110000):

  •  Solder JTAG cable to HTC DesireV (PL1110000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC DesireV (PL1110000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_v_t328w_2

RIFF JTAG – Weekend updates

18.05.2012  RIFF JTAG – Weekend updates:

Whats new:

  • Samsung B7320 unbrick/boot repair support added
  • HTC Sensation 4G (PG581000) Unbrick, Unlock, S-Off, SuperCID support added
  • HTC Sensation (PG581300/PG583101) Unlock support added
  • HTC Evo 3D Unlock support added

Bug Fix updates:

  • HTC Desire HD Support for new board revisions with hboot 2.xx
  • HTC Wildfire S Proximity sensor fix

RIFF Torrent tracker:

Please click “Check for updates” button in RIFF JTAG Manager to download new files.
.

RIFF JTAG – HTC via USB Cable Support added

24.04.2012  RIFF JTAG – HTC via USB Cable Support added

Whats new:
Released support for HTC phones based on MSM8x55 CPU, which are enumerated on USB port as “QHUSB_DLOAD” device. Now it’s possible to repair these phones without soldering any wires. Even without opening !

Following models are supported at the moment:

  • HTC Desire HD (HTC Ace)
  • HTC Desire S (HTC Saga)
  • HTC Desire Z (HTC Vision)
  • HTC Flyer 3G
  • HTC Flyer WiFi
  • HTC Evo View 4G
It is possible to force QHUSB_DLOAD mode by disabling Vdd line on eMMC chip. Check Desire S TP info for example. This means, You can work with any MSM8255/MSM8655 based HTC phone, as long as You force it into QHUSB_DLOAD mode.
Follow this procedure if You want to use these updates:
  • Connect Your phone to USB port and install QHUSB_DLOAD device driver (C:\Program Files (x86)\RIFF Box JTAG Manager\Drivers\32Bit\QDLOADER)
  • Launch JTAG Manager, select appropriate Model DLL and click desired button
  • Install “RIFF Box DCCLoader USB Interface” port driver (C:\Users\Admin\Desktop\Drivers_64Bit_WorkedForMe\Drivers\64Bit\DCCLDR)
  • If required, repeat the procedure (sometimes required if device is connected for first time)

We will release USB support for rest of the models on these CPU-s in following days.

To download and install new updates – simply click “Check for Updates” button on Box Service TAB.

RIFF JTAG – HTC Desire CDMA Supported

24.10.2011  HTC Desire CDMA Supported

Resurrecting HTC Desire CDMA is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.60.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PP9940000’.
Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC Desire CDMA:

  •  Solder JTAG cable to HTC Desire CDMA JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire CDMA is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Back’ key and press ‘Power ON’ button.

RIFF JTAG – HTC Desire Z (HTC Vision) Unbrick, Unlock, IMEI&CID repair supported

12.10.2011    HTC Desire Z (HTC Vision) Unbrick, Unlock, IMEI&CID repair supported

Resurrecting HTC Desire Z is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Desire Z boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM7230 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.

Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write one of selected PDA’s SPL versions (0.76.2000 or 0.85.0005). Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC1010000’.
There is option to reflash BOOT and RECOVERY zones.

Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Desire Z:

  •  Solder JTAG cable to HTC Desire Z JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Desire Z is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

RIFF JTAG – HTC Desire S S510E (HTC Saga) – Unbrick, Unlock, CID, IMEI Update supported

09.09.2011  HTC Desire S S510E (HTC Saga) – Unbrick, Unlock, CID, IMEI Update supported
Resurrecting HTC Desire S is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Desire S boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL to 0.98.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG8810000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.
To resurrect HTC Desire S:

  •  Solder JTAG cable to HTC Desire S JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Desire S is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.