RIFF JTAG – JTAG Manager v1.40 Released

29.02.2012    JTAG Manager v1.40 Released

Whats new:

  • Solved the problem with download of updates. Now no more nasty ‘Out of Disk Space’ error!!!Some users could experience this kind of error during download of large files (30MB and more). These errors were often with Wi-Fi configurations where certain routers dind’t handled passive ports FTP data transfers properly.
  • Added check if JTAG Manager is running with administrator rights (in case it is installed in Program Files location).
    This solves issues for older operating systems (Windows XP) which have no UAC and no manifest means controlling elevation of application rights. Thus –  now if the JTAG Manager is started without administator rights it will restart itself with request to run it “as administrator”.
  • Embedded font for text message window on JTAG Read/Write page.
  • Improved displaying of DLL version information: If FileVersion info is available JTAG Manger will display it rather than the internal version supplied by DLL.
    This simplifies version tracking for us.
  • Download speed limit is increased to 250kb/s

Please click “Check for Updates” button in order to download and apply new updates.

RIFF JTAG – Samsung T749, Samsung E189 Unbrick – Boot repair supported

12.07.2011 Samsung T749, Samsung E189 Unbrick – Boot repair supported

The Samsung T749 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect Samsung T749:

  •  Solder JTAG cable to Samsung T749 JTAG pads;
  •  Connect USB cable;
  •  Make sure Samsung T749 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
In case you cannot find firmware files use Global RIFF Link & Data Exchange plugin – at the moment of resurrector release there was shared full dump from alive Samsung T749 phone.
To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button.

 

 

 

Resurrecting Samsung E189 is simple.
Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x2256
To resurrect Samsung E189:

  •  Solder JTAG cable to Samsung E189 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung E189 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA day again, 3 new models supported

22.06.2011  CDMA day again, 3 new models supported

Whats new:

  • Motorola W200 full support
  • Huawei C2801 full support
  • Nokia 1006   full support

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – More CDMA Models, new bug fix updates today

10.06.2011  More CDMA Models, new bug fix updates today

Whats new :

CDMA  Models JTAG support :

  • Huawei C2605
  • Micromax  MMX 250C
  • ZTE  WP829
  • LG RD3640

Bug fix updates :

  • Samsung S5830
  • HTC Incredible C

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – More CDMA Models, Samsung S5250 Unbrick supported

29.05.2011   More CDMA Models, Samsung S5250 Unbrick supported

New CDMA models added today :

  • ZTE S160
  • Unicare  UN510BF
  • Unicare ChivaC2
  • Huawei C5100

Samsung phones :

  • Samsung S5250
  • Samsung S5260 (Bug Fix)

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Dopod Magic A6188 (HTC Sapp400) Unbrick, Unlock, IMEI and CID repair supported

Dopod Magic A6188 (HTC Sapp400) Unbrick, Unlock, IMEI and CID repair supported

The HTC Magic (SAPP400) is based on ESM7206A chipset. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.53.02000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘SAPP*****’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC Magic (SAPP400):

  • Solder JTAG cable to HTC Magic (SAPP400) JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Magic (SAPP400) is selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘Back (←)’ key and press ‘Power ON’ button. In few seconds you should see download mode saying Fastboot USB.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Day Again :) More power for Indian users !

09.05.2011  RIFF JTAG – CDMA Day Again 🙂 More power for Indian users !

Whats new:

Added Huawei CDMA models support :

  • Huawei C2823 Repair, Read/Write NOR flash
  • Huawei C2809 Repair, Read/Write NOR flash
  • Huawei C2808 Repair, Read/Write NOR flash
  • Huawei C2807 Repair, Read/Write NOR flash
  • Huawei C2607 Repair, Read/Write NOR flash
  • Huawei C2905 Repair, Read/Write NOR flash

Added ZTE CDMA Model :

  • ZTE C335  Repair, Read/Write NOR flash

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC Polaris (HTC Cruise) Unbrick, Unlock, IMEI and CID Update, ModelID repair supported

12.04.2011   HTC Polaris (HTC Cruise) Unbrick, Unlock, IMEI and CID Update, ModelID repair supported

Resurrecting HTC Polaris is easy.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.20.AxeBox. Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘POLA10000’.

To resurrect HTC Polaris:

  • Solder JTAG cable to HTC Polaris JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Polaris selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – RIFF Data Exchange Plugin 1.00 released

31.03.2011 RIFF Data Exchange Plugin 1.00 released
First release of the RIFF Data Exchange Plugin: please download it, and then select it on Usefull Plugins page in the JTAG Manager to read short description about the plugin’s abilities. In short it allows RIFF BOX users to share and use Full Image files in centralized manner without need to waste a lot of time for browsing countless forums.

Because of big sizes of Full Image files, we don’t host them, instead users share links to file sharing servers where the files are actually uploaded. (like megaupload.com, rapidshare.com and others) You can browse existent links for required image file or share your image file (by sharing a http link) to help other RIFF BOX users.

If you share image file please take attention to carefully fill file details so for other people this to be an easy task to search for required file (link)
If you used link to download file and found it good or bad or link to be broken – please Rate this link so other users see the usability of the link.
At the moment of first release of this plugin there are already few links shared so you’ll catch the idea fast.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – RIFF Box firmware v1.21 released

21.03.2011  RIFF Box firmware v1.21 released

Whats new:

  • Added RX-polling feature (debugger-to-target) for PXA3XX DCC transfers.

RIFF BOX firmware is able now to wait (if resurrector DLL will request so) for PXA3XX target to be ready to accept
next packet over DCC: this feature slows down a little the JTAG-to-Target DCC
transfers but guaranties no packets loss for slow clocked targets;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.