RIFF Box – Best JTAG Box in this Galaxy :) Easy to operate !

RIFF JTAG – Easy repair Sony Xperia Miro ST23 / ST23i (Sony Mesona) supported

Repairing bricked SE ST23i is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.

To resurrect SE ST23i:

•  Solder JTAG cable to SE ST23i JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure SE ST23i is selected in the list of models;
•  If you use battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.

RIFF JTAG – Easy repair Sony Xperia TX LT29 / Xperia T LT29i (Sony Hayabusa) supported

Repairing bricked SE LT29i is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.

To resurrect SE LT29i:

•  Solder JTAG cable to SE LT29i JTAG pads;
•  Insert batter and connect USB Data cable;
•  Make sure SE LT29i is selected in the list of models;
•  If you use only battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
.

RIFF JTAG – Easy repair Sony Xperia S LT26 / LT26i / Arc HD (Sony Nozomi) supported

Repairing bricked SE LT26i is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.

To resurrect SE LT26i:

•  Solder JTAG cable to SE LT26i JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure SE LT26i is selected in the list of models;
•  If you use battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.

RIFF JTAG – Easy repair HTC One mini LTE 601n (HTC M4) supported

Repairing bricked HTC OneMini (PO5820000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.19.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PO5820000’.

To resurrect HTC OneS:

•  Solder JTAG cable to HTC OneMini (PO5820000) JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure HTC OneMini (PO5820000) is selected in the list of models;
•  If you use battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Easy repair Lenovo/Acer Gobi 2000 modem card supported

Resurrecting Qualcomm ThinkPad GOVI2000 is simple.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0×0020/0×8829.

To resurrect Qualcomm ThinkPad GOVI2000:

•  Solder JTAG cable to Qualcomm ThinkPad GOBI2000 JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure Qualcomm ThinkPad GOVI2000 is selected in the list of models;
•  Click Resurrect button;
•  Choose which areas to flash;
•  Wait till software signals a successful operation completion;
•  De-solder JTAG wires;

You can select Acer or Lenovo firmware version.

..

RIFF JTAG – Easy repair CDMA ZTE C132 Striker supported

Resurrecting ZTE C132 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0×0063.

To resurrect ZTE C132:

•  Solder JTAG cable to ZTE C132 JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure ZTE C132 is selected in the list of models;
•  Click Resurrect button;
•  Choose which areas to flash;
•  Wait till software signals a successful operation completion;
•  De-solder JTAG wires;

.

RIFF JTAG – Easy repair CDMA ZTE S183 supported

Resurrecting ZTE S183 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0×0063.

To resurrect ZTE S183:

•  Solder JTAG cable to ZTE S183 JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure ZTE S183 is selected in the list of models;
•  Click Resurrect button;
•  Choose which areas to flash;
•  Wait till software signals a successful operation completion;
•  De-solder JTAG wires;

.

RIFF JTAG – Easy repair CDMA Alcatel C131 supported

Resurrecting Alcatel C131 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0×0063.

To resurrect Alcatel C131:

•  Solder JTAG cable to Alcatel C131 JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure Alcatel C131 is selected in the list of models;
•  Click Resurrect button;
•  Choose which areas to flash;
•  Wait till software signals a successful operation completion;
•  De-solder JTAG wires;

.