RIFF JTAG – Samsung Galaxy Ace Duos I589 Unbrick – dead boot repair supported

28.09.2013 RIFF JTAG – Samsung Galaxy Ace Duos I589 Unbrick – dead boot repair supported

Repairing bricked Samsung I589 is easy with the RIFF Box. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung I589 do this:

  •  Solder JTAG cable to Samsung I589 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung I589 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
.
samsung-galaxy-ace-duos-sch-i589-400x365

RIFF JTAG – Samsung 4G LTE Mobile Hotspot SCH-LC11 Unbrick supported

28.09.2013   RIFF JTAG – Samsung 4G LTE Mobile Hotspot SCH-LC11 Unbrick supported

Repairing bricked Samsung LC11 is easy with the RIFF Box.

To resurrect Samsung LC11:

  •  Solder JTAG cable to Samsung LC11 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung LC11 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now device is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.
c4d35_samsung_Verizon-samsung-SCH-LC11-modem

RIFF JTAG – Samsung GT-S7572 Galaxy Trend Duos II Unbrick – Total Repair supported

10.08.2013  RIFF JTAG – Samsung GT-S7572 Galaxy Trend Duos II Unbrick – Total Repair supported

Repairing bricked Samsung S7572 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7572:

  •  Solder JTAG cable to Samsung S7572 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7572 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_galaxy_trend_duos_2

RIFF JTAG – Samsung GT-i9158 Galaxy Mega 5.8 Unbrick – Total Repair supported

10.08.2013  RIFF JTAG – Samsung GT-i9158 Galaxy Mega 5.8 Unbrick  – Total Repair supported

Repairing bricked Samsung I9158 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung I9158:

  •  Solder JTAG cable to Samsung I9158 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung I9158 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_galaxy_mega_5.8_gt_9158

RIFF JTAG – Samsung GT-i8552 Galaxy Win Duos / Galaxy Grand Quattro Unbrick – Total Repair supported

10.08.2013  RIFF JTAG – Samsung GT-i8552 Galaxy Win Duos / Galaxy Grand Quattro Unbrick – Total Repair supported

Repairing bricked Samsung I8552 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung I8552:

  •  Solder JTAG cable to Samsung I8552 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung I8552 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_gt-i8552_galaxy_win_duos

RIFF JTAG – Samsung SCH-i545 Galaxy S4 (Samsung Altius) Unbrick – Total Repair supported

10.08.2013  RIFF JTAG – Samsung SCH-i545 Galaxy S4 (Samsung Altius) Unbrick – Total Repair supported

Repairing bricked Samsung I545 is easy with the RIFF Box.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted. Please note, battery must be charged. If battery is not charged enough there is chance of getting 0x42 error during connection stage.
During Resurrection process you can select areas to be resurrected. Select them wisely: selecting everything in one bunch may just increase flashing time while it’s possible that all you need is to repair only few certain areas.

To resurrect Samsung I545:

  •  Solder JTAG cable to Samsung I545 JTAG pads;
  •  Connect USB cable or insert battery;
  •  Make sure Samsung I545 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.
samsung_sch-545_galaxy_s4

RIFF JTAG – Samsung SGH-i337M Galaxy S 4 LTE 32GB (Samsung Altius) Unbrick Total Repair supported

10.08.2013  RIFF JTAG – Samsung SGH-i337M Galaxy S 4 LTE 32GB (Samsung Altius) Unbrick Total Repair supported

Repairing bricked Samsung I337M is easy with the RIFF Box.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted. Please note, battery must be charged. If battery is not charged enough there is chance of getting 0x42 error during connection stage.
During Resurrection process you can select areas to be resurrected. Select them wisely: selecting everything in one bunch may just increase flashing time while it’s possible that all you need is to repair only few certain areas.

To resurrect Samsung I337M:

  •  Solder JTAG cable to Samsung I337M JTAG pads;
  •  Connect USB cable or insert battery;
  •  Make sure Samsung I337M is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.
samsung_galaxy_s_4_4

RIFF JTAG – LG F260S Optimus LTE III boot repair supported

10.08.2013  RIFF JTAG – LG F260S Optimus LTE III boot repair supported

Repairing bricked LG F260S with the RIFF Box requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted. Please note, battery must be charged. If battery is not charged enough there is chance of getting 0x42 error during connection stage.

To resurrect LG F260S:

  •  Solder JTAG cable to LG F260S JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG F260S is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume down’ and ‘Camera’ keys and press ‘Power ON’ button.

.
lg_optimus_lte_iii

RIFF JTAG – LG E975 Optimus G (LG Gee) boot repair supported

10.08.2013  RIFF JTAG – LG E975 Optimus G (LG Gee) boot repair supported

Repairing bricked LG E975 with the RIFF Box requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted. Please note, battery must be charged. If battery is not charged enough there is chance of getting 0x42 error during connection stage.

To resurrect LG E975:

  •  Solder JTAG cable to LG E975 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E975 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume down’ and ‘Camera’ keys and press ‘Power ON’ button.

.
lg_optimus_g_4

RIFF JTAG – LG E960 Nexus 4 (LG Mako) boot repair supported

10.08.2013  RIFF JTAG – LG E960 Nexus 4 (LG Mako) boot repair supported

Repairing bricked LG E960 with the RIFF Box requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted. Please note, battery must be charged. If battery is not charged enough there is chance of getting 0x42 error during connection stage.

To resurrect LG E960:

  •  Solder JTAG cable to LG E960 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E960 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume down’ and ‘Camera’ key

.
lg_e960_nexus_4