RIFF JTAG – Samsung SHW-M250S Galaxy S II Unbrick – dead boot repair supported

31.08.2013   RIFF JTAG – Samsung SHW-M250S Galaxy S II Unbrick – dead boot repair supported

Samsung M250S is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung M250S:

  •  Solder JTAG cable to Samsung M250S JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung M250S is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_shw-m250s_galaxy_s_ii

RIFF JTAG – Samsung GT-S7572 Galaxy Trend Duos II Unbrick – Total Repair supported

10.08.2013  RIFF JTAG – Samsung GT-S7572 Galaxy Trend Duos II Unbrick – Total Repair supported

Repairing bricked Samsung S7572 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7572:

  •  Solder JTAG cable to Samsung S7572 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7572 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_galaxy_trend_duos_2

RIFF JTAG – Samsung GT-i9158 Galaxy Mega 5.8 Unbrick – Total Repair supported

10.08.2013  RIFF JTAG – Samsung GT-i9158 Galaxy Mega 5.8 Unbrick  – Total Repair supported

Repairing bricked Samsung I9158 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung I9158:

  •  Solder JTAG cable to Samsung I9158 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung I9158 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_galaxy_mega_5.8_gt_9158

RIFF JTAG – Samsung GT-i9152 Galaxy Mega 5.8 Unbrick Total Repair supported

10.08.2013  RIFF JTAG – Samsung GT-i9152 Galaxy Mega 5.8 Unbrick Total Repair supported

Samsung I9152 is based on the Broadcom BCM28145 Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I9152:

  •  Solder JTAG cable to Samsung I9152 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9152 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_galaxy_mega_5.8

RIFF JTAG – Samsung GT-i8552 Galaxy Win Duos / Galaxy Grand Quattro Unbrick – Total Repair supported

10.08.2013  RIFF JTAG – Samsung GT-i8552 Galaxy Win Duos / Galaxy Grand Quattro Unbrick – Total Repair supported

Repairing bricked Samsung I8552 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung I8552:

  •  Solder JTAG cable to Samsung I8552 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung I8552 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_gt-i8552_galaxy_win_duos

RIFF JTAG – Samsung GT-i9105P Galaxy S II Plus Unbrick – Dead boot repair supported

27.05.2013  RIFF JTAG – Samsung GT-i9105P Galaxy S II Plus Unbrick – Dead boot repair supported

Samsung I9105P is based on the Broadcom BCM28145 Processor (Cortex-A9 Dual-Core).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I9105:

  •  Solder JTAG cable to Samsung I9105P JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9105P is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_gt-i9105_galaxy_s_ii_plus_2

RIFF JTAG – Samsung GT-i9105 Galaxy S II Plus Unbrick – Dead boot repair supported

27.05.2013  RIFF JTAG – Samsung GT-i9105 Galaxy S II Plus Unbrick – Dead boot repair supported

Samsung I9105 is based on the Broadcom BCM28145 Processor (Cortex-A9 Dual-Core).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I9105:

  •  Solder JTAG cable to Samsung I9105 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9105 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_gt-i9105_galaxy_s_ii_plus_2

RIFF JTAG – Samsung GT-i9082 Galaxy Grand Duos (Samsung Baffin) Unbrick – Dead boot repair supported

27.05.2013  RIFF JTAG – Samsung GT-i9082 Galaxy Grand Duos (Samsung Baffin)  Unbrick – Dead boot repair supported

Samsung I9082 is based on the Broadcom BCM28155 Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I9082:

  •  Solder JTAG cable to Samsung I9082 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9082 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_gt-i9080_galaxy_grand

RIFF JTAG – Samsung GT-S7500T Galaxy Ace Plus Unbrick – Dead boot repair supported

19.04.2013 RIFF JTAG – Samsung GT-S7500T Galaxy Ace Plus Unbrick – Dead boot repair supported

Resurrecting Samsung S7500T is easy with RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7500T:

  •  Solder JTAG cable to Samsung S7500T JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7500T is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

samsung_ace_plus

RIFF JTAG – Samsung GT-i8190 Galaxy S III Mini Unbrick – Dead boot repair supported

29.03.2013  RIFF JTAG – Samsung GT-i8190 Galaxy S III Mini Unbrick – Dead boot repair supported

Repairing bricked Samsung I8190 is easy with the RIFF Box.
Please note, USB cable must be either disconnected or connected to PC. Charger is not allowed. In order to establish connection, insert battery and press Power On.
Problem to establish JTAG connection means the device is dead up to the loader which enables JTAG. In this case phone must be detected via USB cable as “U8500 USB ROM”. Please install drivers which are located in JTAG Manager “Drivers\NTU8500” folder, leave USB cable connected and start resurrection again.

To resurrect Samsung I8190:

  •  Solder JTAG cable to Samsung I8190 JTAG pads;
  •  Attach battery and connect USB cable;
  •  Make sure Samsung I8190 is selected in the list of models;
  •  Click Resurrect button;
  •  If required, press Power On key;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_gt-i8190_galaxy_s_iii_mini_2