RIFF JTAG – Samsung SHW-M250S Galaxy S II Unbrick – dead boot repair supported

31.08.2013   RIFF JTAG – Samsung SHW-M250S Galaxy S II Unbrick – dead boot repair supported

Samsung M250S is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung M250S:

  •  Solder JTAG cable to Samsung M250S JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung M250S is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_shw-m250s_galaxy_s_ii

RIFF JTAG – Samsung GT-i9152 Galaxy Mega 5.8 Unbrick Total Repair supported

10.08.2013  RIFF JTAG – Samsung GT-i9152 Galaxy Mega 5.8 Unbrick Total Repair supported

Samsung I9152 is based on the Broadcom BCM28145 Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I9152:

  •  Solder JTAG cable to Samsung I9152 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9152 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_galaxy_mega_5.8

RIFF JTAG – Samsung GT-i9105P Galaxy S II Plus Unbrick – Dead boot repair supported

27.05.2013  RIFF JTAG – Samsung GT-i9105P Galaxy S II Plus Unbrick – Dead boot repair supported

Samsung I9105P is based on the Broadcom BCM28145 Processor (Cortex-A9 Dual-Core).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I9105:

  •  Solder JTAG cable to Samsung I9105P JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9105P is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_gt-i9105_galaxy_s_ii_plus_2

RIFF JTAG – Samsung GT-i9105 Galaxy S II Plus Unbrick – Dead boot repair supported

27.05.2013  RIFF JTAG – Samsung GT-i9105 Galaxy S II Plus Unbrick – Dead boot repair supported

Samsung I9105 is based on the Broadcom BCM28145 Processor (Cortex-A9 Dual-Core).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I9105:

  •  Solder JTAG cable to Samsung I9105 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9105 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_gt-i9105_galaxy_s_ii_plus_2

RIFF JTAG – Samsung GT-i9082 Galaxy Grand Duos (Samsung Baffin) Unbrick – Dead boot repair supported

27.05.2013  RIFF JTAG – Samsung GT-i9082 Galaxy Grand Duos (Samsung Baffin)  Unbrick – Dead boot repair supported

Samsung I9082 is based on the Broadcom BCM28155 Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I9082:

  •  Solder JTAG cable to Samsung I9082 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9082 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_gt-i9080_galaxy_grand

RIFF JTAG – RIFF JTAG Manager v1.49, RIFF Box Firmware v1.35 released (Cortex-A15, Cortex-A5)

24.04.2013   RIFF JTAG – RIFF JTAG Manager v1.49, RIFF Box Firmware v1.35 released (Cortex-A15, Cortex-A5)

Whats new:

RIFF Box Firmware v1.35

  •   Added support for Cortex-A15 and Cortex-A5 cores.
  •   Fixed emergency script issue for multi-cored Cortex MCUs: it was executed after first core was halted.

Now it is executed after all core(s) (if specified by reset strategy) are processed (halted).

 

RIFF JTAG Manager v1.49

  •   Added support for Cortex-A15 and Cortex-A5 cores.
  •   New Popup balloon is added with hints about ‘Dead Body ID is wrong’ error.
  •   Added Windows 8 support.
  •   Added “RIFFBOX on the Network” button (BOX Service Page).
    User can easily visit some main RIFFBOX’s internet locations.
  •   Some new IDCODES added to the search engine (CTRL+F)

.

riff-network

RIFF JTAG – Samsung SHW-M200K NEXUS S Unbrick – Dead boot repair supported

29.03.2013  RIFF JTAG – Samsung SHW-M200K NEXUS S Unbrick – Dead boot repair supported

Repairing bricked Samsung M200K is easy with the RIFF Box. The phone is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.

To resurrect Samsung M200K:

  •  Solder JTAG cable to Samsung M200K JTAG pads;
  •  Connect microUSB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung M200K is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

Samsung-Google-Nexus-S-i9020A

RIFF JTAG – Samsung GT-P3113 Galaxy Tab 2 7.0 Unbrick – Dead boot repair supported

21.02.2013  RIFF JTAG – Samsung GT-P3113 Galaxy Tab 2 7.0 Unbrick – Dead boot repair supported

Samsung P3113 is based on the OMAP4430 Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Please note: The initial loader in the Samsung P3113 is XLOADER. Due to OMAP4430’s some peculiar TrustZone security features current resurrector will boot only in case XLOADER is alive. That’s why model name of current resurrector has additional text: ‘XLoader+’. In case XLOADER is damaged (which happens for example after wrong firmware reflash), you will have to use different resurrector DLL – the one with the ‘XLoader-” delimiter.

To resurrect Samsung P3113:

  •  Solder JTAG cable to Samsung P3113 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung P3113 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

samsung_galaxy_tab_2_70_2

RIFF JTAG – Samsung GT-P3110 Galaxy Tab 2 7.0 Unbrick – Dead boot repair supported

21.02.2013   RIFF JTAG – Samsung GT-P3110 Galaxy Tab 2 7.0 Unbrick – Dead boot repair supported

Samsung P3110 is based on the OMAP4430 Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Please note: The initial loader in the Samsung P3110 is XLOADER. Due to OMAP4430’s some peculiar TrustZone security features current resurrector will boot only in case XLOADER is alive. That’s why model name of current resurrector has additional text: ‘XLoader+’. In case XLOADER is damaged (which happens for example after wrong firmware reflash), you will have to use different resurrector DLL – the one with the ‘XLoader-” delimiter.

To resurrect Samsung P3110:

  •  Solder JTAG cable to Samsung P3110 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung P3110 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.
samsung_galaxy_tab_2_70_2

RIFF JTAG – Samsung GT-P3100 Galaxy Tab 2 7.0 Unbrick – Dead boot repair supported

21.02.2013  RIFF JTAG – Samsung GT-P3100 Galaxy Tab 2 7.0 Unbrick – Dead boot repair supported

Samsung P3100 is based on the OMAP4430 Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Please note: The initial loader in the Samsung P3100 is XLOADER. Due to OMAP4430’s some peculiar TrustZone security features current resurrector will boot only in case XLOADER is alive. That’s why model name of current resurrector has additional text: ‘XLoader+’. In case XLOADER is damaged (which happens for example after wrong firmware reflash), you will have to use different resurrector DLL – the one with the ‘XLoader-” delimiter.

To resurrect Samsung P3100:

  •  Solder JTAG cable to Samsung P3100 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung P3100 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.
samsung_galaxy_tab_2_70