Tag Archives: Memory Chip

RIFF JTAG – Haier C2010 Ubrick – Dead Boot repair supported

Posted on by

29.12.2012   RIFF JTAG – Haier C2010 Ubrick – Dead Boot repair supported

Resurrecting Haier C2010 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0020/0x8832

To resurrect Haier C2010:

  •  Solder JTAG cable to Haier C2010 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Haier C2010 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

.
haier-c2010-mobile-phone-medium-1

RIFF JTAG – Samsung SCH-E329I Unbrick – Dead Boot Repair Supported

Posted on by

11.10.2012  RIFF JTAG – Samsung SCH-E329I Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung E329I is easy with the RIFF Box. Please note, by default, NRST pad is disabled in this phone. In case you have any troubles with resurrection, shortcut pads A and B shown in shematics in order to enable NRST.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x3013

To resurrect Samsung E329I:

  •  Solder JTAG cable to Samsung E329I JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung E329I is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

.

RIFF JTAG – STB Orton 4100C Unbrick supported

Posted on by

06.04.2012    RIFF JTAG – STB Orton 4100C Unbrick supported

Repairing bricked Orton 4100C is easy with the RIFF Box. Receiver is based on the ALI M3329C processor. Receiver is powered on when power plug is attached. If connection process stops at “Establish communication with the phone…” just reset the receiver’s power.
Current resurrector contains Boot, Firmware and Data zones which in total is complete full connects for 2Mb SPI serial memory chip.
Please note, to enable JTAG you have to make sure the JP1 jumper on board is not shorted. Sometimes you may need to disconnect front LED panel interface cable from the board (13-pin connector). After resurrection do not forget to solder the resistor back or shortcut JP1 jumper.
To resurrect Orton 4100C:

  •  Solder JTAG cable to Orton 4100C JTAG pads;
  •  Make sure Orton 4100C is selected in the list of models;
  •  Connect power;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Now receiver is in bootable condition, that is, even if it does not start up normally you can flash it via UART using known flashing methods. Or you can do resurrection checking full clone resurrect option – this will re-write all flash memory contents.
.

RIFF JTAG – STB EuroSky ES-4100 Unbrick supported

Posted on by

06.04.2012   RIFF JTAG – STB EuroSky ES-4100 Unbrick supported

Repairing bricked EuroSky ES-4100 is easy with the RIFF Box. Receiver is based on the ALI M3329C processor. Receiver is powered on when power plug is attached. If connection process stops at “Establish communication with the phone…” just reset the receiver’s power.
Current resurrector contains Boot, Firmware and Data zones which in total is complete full connects for 2Mb SPI serial memory chip.
Please note, to enable JTAG you have to make sure the JP1 jumper on board is not shorted, desolder resistor R65. Sometimes you may need to disconnect front LED panel interface cable from the board (13-pin connector). After resurrection do not forget either to solder the resistor back or shortcut JP1 jumper.

To resurrect EuroSky ES-4100:

  •  Solder JTAG cable to EuroSky ES-4100 JTAG pads;
  •  Make sure EuroSky ES-4100 is selected in the list of models;
  •  Connect power;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Now STB is in bootable condition, that is, even if it does not start up normally you can flash it via UART using known flashing methods. Or you can do resurrection checking full clone resurrect option – this will re-write all flash memory contents.
.

RIFF JTAG – Lynksis Router LinkSys WRT54G unbrick supported

Posted on by

06.04.2012 RIFF JTAG – Lynksis Router LinkSys WRT54G unbrick supported
Repairing bricked LinkSys WRT54GL is easy with the RIFF Box. Router is powered on when power plug is attached. If connection process stops at “Establish communication with the phone…” just reset router’s power.
Current resurrector contains Boot, Configuration and Firmware zones for memory chip with ID 0x00C2/0x22A8

To resurrect LinkSys WRT54GL:

  •  Solder JTAG cable to LinkSys WRT54GL JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LinkSys WRT54GL is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Now router is in bootable condition, that is, even if it does not start up normally you can flash it via UART using known flashing methods. Or you can do resurrection checking full clone resurrect option – this will re-write all flash memory contents.
.

RIFF JTAG – CDMA Olive C2110 Supported

Posted on by

27.12.2011    CDMA Olive C2110 Supported

Resurrecting Olive C2110 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x2254

To resurrect Olive C2110:

  •  Solder JTAG cable to Olive C2110 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Olive C2110 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG – CDMA Samsung B339 Breeze Supported

Posted on by

23.12.2011 CDMA Samsung B339 Breeze Supported

Resurrecting Samsung B339 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x2256

To resurrect Samsung B339:

  •  Solder JTAG cable to Samsung B339 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung B339 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG – CDMA Huawei C3500 Supported

Posted on by

23.12.2011    CDMA Huawei C3500 Supported 

Resurrecting Huawei C3500 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Huawei C3500:

  •  Solder JTAG cable to Huawei C3500 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Huawei C3500 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG – CDMA Huawei C2856 Supported

Posted on by

22.11.2011  CDMA Huawei C2856 Supported

Resurrecting Huawei C2856 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0020/0x88C0

To resurrect Huawei C2856:

  •  Solder JTAG cable to Huawei C2856 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Huawei C2856 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG – CDMA Haier C301R supported

Posted on by

20.12.2011   CDMA Haier C301R supported

Resurrecting Haier C301R is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Haier C301R:

  •  Solder JTAG cable to Haier C301R JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Haier C301R is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;