RIFF JTAG – Easy repair Sony Xperia Tipo Dual ST21i2 (Sony Tapioca DS) supported

RIFF JTAG – Easy repair Sony Xperia Tipo Dual ST21i2 (Sony Tapioca DS)  supported

Repairing bricked SE ST21i2 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.

To resurrect SE ST21i2:

  •  Solder JTAG cable to SE ST21i2 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure SE ST21i2 is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.
sony_xperia_tipo_dual

RIFF JTAG – Asus Padfone 2 A68 Unbrick – dead boot repair supported

28.09.2013  RIFF JTAG – Asus Padfone 2 A68  Unbrick – dead boot repair supported

Repairing bricked Asus Padfone A68 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.

To resurrect Asus Padfone A68:

  •  Solder JTAG cable to Asus Padfone A68 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Asus Padfone A68 is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

.
asus_padfone2_2

RIFF JTAG – Asus Padfone Infinity A80 Unbrick – dead boot repair supported

28.09.2013  RIFF JTAG – Asus Padfone Infinity A80 Unbrick – dead boot repair supported

Repairing bricked Asus Padfone A80 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.

To resurrect Asus Padfone A80:

  •  Solder JTAG cable to Asus Padfone A80 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Asus Padfone A80 is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

.
asus_padfone_infinity_2

RIFF JTAG – HTC T329w (HTC Proto) Unbrick – SuperCID – IMEI repair supported

28.09.2013  RIFF JTAG – HTC T329w (HTC Proto) Unbrick – SuperCID – IMEI repair supported

Repairing bricked HTC Proto (PM6610000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.12.0002 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PM661****’.

To resurrect HTC Proto (PM6610000):

  •  Solder JTAG cable to HTC Proto (PM6610000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Proto (PM6610000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_x

RIFF JTAG – HTC One LTE 32GB (HTC M7) Unbrick, Unlock, IMEI and SuperCID supported

27.06.2013   RIFF JTAG – HTC One LTE 32GB (HTC M7) Unbrick, Unlock, IMEI and SuperCID supported

Repairing bricked HTC OneM7 (PN0710000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.44.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PN0710000’.

To resurrect HTC OneS:

  •  Solder JTAG cable to HTC OneM7 (PN0710000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneM7 (PN0710000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_3

RIFF JTAG – HTC One VX (HTC Totem C2) Supported

03.06.2013  RIFF JTAG – HTC One VX (HTC Totem C2) Supported

Repairing bricked HTC OneVX (PM3610000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.31.0013 version. Additionally to SPL and Radio zOneVX, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PM3610000’.

To resurrect HTC OneVX:

  •  Solder JTAG cable to HTC OneVX JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneVX (PM3610000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_vx

RIFF JTAG – HTC Desire SV T326e (HTC Magni) Unbrick – Dead boot repair supported

27.05.2013  RIFF JTAG – HTC Desire SV T326e (HTC Magni) Unbrick – Dead boot repair supported

Repairing bricked HTC Desire SV (PM8610000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.35.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PM8610000’.

To resurrect HTC Desire SV (PM8610000):

  •  Solder JTAG cable to HTC Desire SV (PM8610000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire SV (PM8610000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_sv_3

RIFF JTAG – HTC Desire VC T328d Unbrick – dead boot repair supported

09.05.2013  RIFF JTAG – HTC Desire VC T328d Unbrick – dead boot repair supported

Repairing bricked HTC DesireVC (PK7810000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.27.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PK7810000’.

To resurrect HTC DesireVC (PK7810000):

  •  Solder JTAG cable to HTC DesireVC (PK7810000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC DesireVC (PK7810000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_vc_t328d_2

RIFF JTAG – LG E405 Optimus L3 Dual Unbrick – Dead boot repair supported

29.03.2013  RIFF JTAG – LG E405 Optimus L3 Dual Unbrick – Dead boot repair supported

Repairing bricked LG E405 with the RIFF Box is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG E405:

  •  Solder JTAG cable to LG E405 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E405 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button.

.
lg_e405_optimus_l3_dual

RIFF JTAG – LG E615 Optimus L5 Dual Unbrick – Dead boot repair supported

29.03.2013   RIFF JTAG – LG E615 Optimus L5 Dual Unbrick – Dead boot repair supported

Repairing bricked LG E615 with the RIFF Box is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG E615:

  •  Solder JTAG cable to LG E615 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E615 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button.

.
lg_e610_optimus_l5