Tag Archives: Htc

RIFF JTAG – HTC One VX (HTC Totem C2) Supported

Posted on by

03.06.2013  RIFF JTAG – HTC One VX (HTC Totem C2) Supported

Repairing bricked HTC OneVX (PM3610000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.31.0013 version. Additionally to SPL and Radio zOneVX, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PM3610000’.

To resurrect HTC OneVX:

  •  Solder JTAG cable to HTC OneVX JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneVX (PM3610000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_vx

RIFF JTAG – HTC J ISW13HT (HTC Valente) Unbrick – Dead boot repair supported

Posted on by

27.05.2013  RIFF JTAG – HTC J ISW13HT (HTC Valente) Unbrick – Dead boot repair supported

Repairing bricked HTC Valente (PK0710000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PK0710000’.

To resurrect HTC Valente (PK0710000):

  •  Solder JTAG cable to HTC Valente (PK0710000) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Valente (PK0710000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htcj

RIFF JTAG – HTC Titan X310E (HTC Eternity) Unbrick, Unlock, IMEI and SuperCID repair supported

Posted on by

19.04.2013  RIFF JTAG – HTC Titan X310E (HTC Eternity) Unbrick, Unlock, IMEI and SuperCID repair supported

Repairing bricked HTC Titan (PI3911000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC Titan (PI3911000) boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM chip). In this case the JTAG may be enabled only by firmware itself. This is done by the DBL loader, so if DBL area is damanged and MCU has JTAG Disable FUSE blown then there is no way to resurrect your phone via JTAG interface. However, in this case you may use HTC Titan (PI3911000) USB DLL version which does not require JTAG interface and does resurrection procedure via USB cable.
Resurrector will reflash radio’s boot zone (except DBL area) and will re-write PDA’s SPL. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PI3911000’.

To resurrect HTC Titan (PI3911000):

  •  Solder JTAG cable to HTC Titan (PI3911000) JTAG pads;
  •  Insert battery and connect USB Data cable;
  •  Make sure HTC Titan (PI3911000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_titan_x310

RIFF JTAG – HTC One XL (HTC Evita) Unbrick – Dead boot, Unlock, SuperCID, IMEI repair supported

Posted on by

09.02.2013   RIFF JTAG – HTC One XL (HTC Evita) Unbrick – Dead boot, Unlock, SuperCID, IMEI repair supported

Repairing bricked HTC OneXL (PJ8312000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ8312000’.

To resurrect HTC OneXL (PJ8312000):

  •  Solder JTAG cable to HTC OneXL (PJ8312000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneXL (PJ8312000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_xl

RIFF JTAG – HTC One S PJ401000 Unbrick, Unlock, IMEI, SuperCID repair supported

Posted on by

29.12.2012  RIFF JTAG – HTC One S PJ401000 Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC OneS (PJ4010000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.06.0000 or 1.13.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ4010000’.

To resurrect HTC OneS:

  •  Solder JTAG cable to HTC OneS JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneS PJ4010000 is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_s

RIFF JTAG – AT&T HTC Status (HTC ChaCha PH0613000) Ubrick, Boot, IMEI, SuperCID repair supported

Posted on by

29.12.2012  RIFF JTAG – AT&T HTC Status (HTC ChaCha PH0613000) Ubrick, Boot, IMEI, SuperCID repair supported

Repairing bricked HTC ChaCha (HTC Status) (PH0613000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.13.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PH0613000’.

To resurrect HTC ChaCha:

  •  Solder JTAG cable to HTC ChaCha (PH0613000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC ChaCha (PH0613000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_status

RIFF JTAG – HTC One S Z560E (HTC Ville C) Unbrick – Dead Boot Repair Supported

Posted on by

21.11.2012  RIFF JTAG – HTC One S Z560E (HTC Ville C) Unbrick – Dead Boot Repair Supported

Repairing bricked HTC OneS is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.09.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ4020000’.

To resurrect HTC OneS:

  •  Solder JTAG cable to HTC OneS JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneS is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Wildfire S CDMA (HTC Marvel C) Unbrick – Dead Boot Repair and full Support

Posted on by

13.11.2012 RIFF JTAG – HTC Wildfire S CDMA (HTC Marvel C) Unbrick – Dead Boot Repair and full Support

Resurrecting HTC WildFireS CDMA is easy with RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 (for NAND chips with 4Kb page size). Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG7620000’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC WildFireS CDMA:

  •  Solder JTAG cable to HTC WildFireS CDMA JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC WildFireS CDMA is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.

.

RIFF JTAG – HTC One V T320e (HTC Primo) Unbrick, Unlock, SuperCID, IMEI Repair supported

Posted on by

31.05.2012  RIFF JTAG – HTC One V T320e (HTC Primo) Unbrick, Unlock, SuperCID, IMEI Repair supported

Repairing bricked HTC OneV (PK76100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).
In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.16.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PK7610000’.
There is option to reflash android BOOT and RECOVERY zones.

To resurrect HTC OneV via USB Cable:

  •  If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, attach battery and then insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;
  •  Make sure HTC OneVC (PK76100) is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods. You can use CWM recovery to flash any ZIP file – for this during resurrection add BOOT & RECOVERY zones to be resurrected too.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC via USB more phones supported

Posted on by

 27.04.2012   RIFF JTAG – HTC via USB more phones supported

  • HTC Thunderbolt USB support added
  • HTC Sensation XL USB support added
  • HTC Inspire USB support added
  • HTC Incredible S USB support added
  • HTC Incredible 2 USB support added

These new updates will allow You to use USB cable to perform any operation on listed models. Remember that this work if Your phone is enumerated on USB port as QHUSB_Dload or Qualcomm HS-USB QDLoader device.
In case phone is not enumerated, You might need to use test point method first.

Please visit RIFF FAQ section to see how to install drivers, and how to find eMMC Vdd test points:

If You need to repair phone after replacing eMMC chip, these are the steps:
  • Launch eMMC MBR/EBR partitioning tool
  • Open desired partitioning file
  • Click “Load Image from file”
  • Click “Repartition eMMC”
  • Close the eMMC plugin
  • Click “Resurrection” and select all options to be repaired, including IMEI and CID
  • Click “Resurrect”

Please click “Check for updates” button to download and install new updates.