RIFF JTAG – HTC Windows Phone 8S (HTC Rio) Unbrick, Unlock, IMEI, SuperCID repair supported

19.04.2013  RIFF JTAG – HTC Windows Phone 8S (HTC Rio) Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC 8S (PM5910002) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PM5910002’.

To resurrect HTC 8S (PM5910002):

  •  Solder JTAG cable to HTC 8S (PM5910002) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC 8S (PM5910002) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_windows_phone_8s

RIFF JTAG – HTC Windows Phone 8X LTE 16GB Unbrick, Unlock, IMEI, SuperCID repair supported

19.04.2013  RIFF JTAG – HTC Windows Phone 8X LTE 16GB Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC 8X (PM2320000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PM232****’.

To resurrect HTC 8X (PM2320000):

  •  Solder JTAG cable to HTC 8X (PM2320000) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC 8X (PM2320000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_windows_phone_8x_3

RIFF JTAG – HTC EVO 3D CDMA Unbrick, Unlock, IMEI, SuperCID repair supported

19.04.2013   RIFF JTAG – HTC EVO 3D CDMA Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC Evo3D CDMA (PG8610000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s HBOOT version 1.50.0000.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC Evo3D CDMA (PG8610000):

  •  Solder JTAG cable to HTC Evo3D CDMA (PG8610000) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Evo3D CDMA (PG8610000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc-evo-3d

RIFF JTAG – T-Mobile myTouch 4G Slide (HTC Doubleshot) Unbrick, Unlock, IMEI, SuperCID repair supported

19.04.2013  RIFF JTAG – T-Mobile myTouch 4G Slide (HTC Doubleshot) Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC MyTouch4G (PG5910000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s HBOOT version 1.44.1107.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC MyTouch4G (PG5910000):

  •  Solder JTAG cable to HTC MyTouch4G (PG5910000) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC MyTouch4G (PG5910000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

t-mobile_mytouch_4g_slide

RIFF JTAG – HTC Titan X310E (HTC Eternity) Unbrick, Unlock, IMEI and SuperCID repair supported

19.04.2013  RIFF JTAG – HTC Titan X310E (HTC Eternity) Unbrick, Unlock, IMEI and SuperCID repair supported

Repairing bricked HTC Titan (PI3911000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC Titan (PI3911000) boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM chip). In this case the JTAG may be enabled only by firmware itself. This is done by the DBL loader, so if DBL area is damanged and MCU has JTAG Disable FUSE blown then there is no way to resurrect your phone via JTAG interface. However, in this case you may use HTC Titan (PI3911000) USB DLL version which does not require JTAG interface and does resurrection procedure via USB cable.
Resurrector will reflash radio’s boot zone (except DBL area) and will re-write PDA’s SPL. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PI3911000’.

To resurrect HTC Titan (PI3911000):

  •  Solder JTAG cable to HTC Titan (PI3911000) JTAG pads;
  •  Insert battery and connect USB Data cable;
  •  Make sure HTC Titan (PI3911000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_titan_x310

RIFF JTAG – Samsung SCH-R530 Galaxy S III LTE Unbrick – Dead boot repair supported

19.04.2013 RIFF JTAG – Samsung SCH-R530 Galaxy S III LTE Unbrick – Dead boot repair supported

Repairing bricked Samsung R530 is easy with the RIFF Box. The device is based on the Qualcomm MSM8960 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung R530:

  •  Solder JTAG cable to Samsung R530 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung R530 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.
samsung_galaxy_s_iii

RIFF JTAG – NTT DoCoMo Samsung Galaxy S III LTE SC-06D Unbrick – Dead boot repair supported

29.03.2013 RIFF JTAG – NTT DoCoMo Samsung Galaxy S III LTE SC-06D Unbrick – Dead boot repair supported

Repairing bricked Samsung SC-06D is easy with the RIFF Box. The device is based on the Qualcomm MSM8960 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung SC-06D:

  •  Solder JTAG cable to Samsung SC-06D JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung SC-06D is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

samsung_galaxy_s_iii_lte_sc-06d

RIFF JTAG – HTC Windows Phone 8X (HTC Accord) Unbrick, Dead boot IMEI repair supported

29.03.2013   RIFF JTAG – HTC Windows Phone 8X (HTC Accord) Unbrick, Dead boot IMEI repair supported

Repairing bricked HTC 8X (PM2330000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PM2330000’.

To resurrect HTC 8X (PM2330000):

  •  Solder JTAG cable to HTC 8X (PM2330000) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC 8X (PM2330000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_windows_phone_8x_2

 

RIFF JTAG – LG E405 Optimus L3 Dual Unbrick – Dead boot repair supported

29.03.2013  RIFF JTAG – LG E405 Optimus L3 Dual Unbrick – Dead boot repair supported

Repairing bricked LG E405 with the RIFF Box is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG E405:

  •  Solder JTAG cable to LG E405 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E405 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button.

.
lg_e405_optimus_l3_dual

RIFF JTAG – LG E615 Optimus L5 Dual Unbrick – Dead boot repair supported

29.03.2013   RIFF JTAG – LG E615 Optimus L5 Dual Unbrick – Dead boot repair supported

Repairing bricked LG E615 with the RIFF Box is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG E615:

  •  Solder JTAG cable to LG E615 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E615 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button.

.
lg_e610_optimus_l5