RIFF JTAG – HTC 7 Surround T8788 (HTC Mondrian) Unbrick, Unlock, SuperCID and IMEI repair supported

23.05.2012  RIFF JTAG – HTC 7 Surround T8788 (HTC Mondrian) Unbrick, Unlock, SuperCID and IMEI repair supported

Repairing bricked HTC Surround (PD26100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.74.1000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD26*****’.

To resurrect HTC Surround (PD26100):

  •  Solder JTAG cable to HTC Surround JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Surround (PD26100) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Samsung SCH-I500 Galaxy S Mesmerize/Fascinate Unbrick Supported

27.03.2012    RIFF JTAG – Samsung SCH-I500 Galaxy S Mesmerize/Fascinate Unbrick Supported

Repairing bricked  Samsung SCH-I500 Galaxy S Mesmerize/Fascinate is easy with RIFF Box.
I500 is based on the S5PCxxx Processor (ARM core is Cortex-A8). Please note the adaptive clocking mode (RTCK) is not available on this processor, so make sure to select a fixed TCK frequency.
To establish the JTAG connection attach battery cable and press Power On key.
In case after resurrection the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung I500:

  •  Solder JTAG cable to Samsung I500 JTAG pads;
  •  Attach battery cable and press Power On key;
  •  Make sure Samsung I500 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
.

RIFF JTAG – HTC EVO 3D (HTC Shooter) Unbrick – Boot Repair Supported, World First ! ! !

14.03.2012   RIFF JTAG – HTC EVO 3D  (HTC Shooter) Unbrick – Boot Repair Supported, World First  ! ! !

Repairing bricked HTC EVO 3D (PG86300) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 1.49.0007. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG8630000’.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC EVO 3D:

  •  Solder JTAG cable to HTC EVO 3D JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC EVO 3D is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Sensation (HTC Pyramid) Unbrick, ModelID, CID, IMEI repair Supported

14.03.2012   RIFF JTAG – HTC Sensation  (HTC Pyramid)  Unbrick, ModelID, CID, IMEI repair Supported

Repairing bricked HTC Sensation is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.

Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 1.18.0000. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG5813000’.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC Sensation:

  •  Solder JTAG cable to HTC Sensation JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Sensation is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – CDMA Sungil SXC1080 Modem supported

30.09.2011   CDMA Sungil SXC1080 Modem supported

 

Resurrecting Sungil SXC1080 is simple.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x22E0

To resurrect Sungil SXC1080:

  •  Solder JTAG cable to Sungil SXC1080 JTAG pads;
  •  Attach battery or external power supply;
  •  Make sure Sungil SXC1080 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

RIFF JTAG – CDMA LG TD636 Unbrick – Boot repair supported

30.08.2011  CDMA LG TD636 Unbrick – Boot repair supported

Resurrecting LG TD636 is simple. To establish connector battery or external power supply must be connected and Power On key to be pressed.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0x2202

To resurrect LG TD636:

  •  Solder JTAG cable to LG TD636 JTAG pads;
  •  Attach battery or external power supply;
  •  Make sure LG TD636 is selected in the list of models;
  •  Press Power On key;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Sony Ericsson Xperia X8a (SE Shakira) Unbrick – Boot repair supported

02.08.2011   Sony Ericsson Xperia X8a (SE Shakira) Unbrick – Boot repair supported

Resurrecting SE X8 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted.
During resurrection, you can select which areas to be repaired. So you can choose only those areas which you know are damaged thus saving flashing time.
To resurrect SE X8:

  •  Solder JTAG cable to SE X8 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure SE X8 is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

 

 

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Sony Ericsson Xperia X10a mini / E10a (SE Robyn) Unbrick – Boot repair supported

02.08.2011    Sony Ericsson Xperia X10a mini / E10a (SE Robyn) Unbrick – Boot repair supported

Resurrecting SE X10 Mini is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted.
During resurrection, you can select which areas to be repaired. So you can choose only those areas which you know are damaged thus saving flashing time.
To resurrect SE X10 Mini:

  •  Solder JTAG cable to SE X10 Mini JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure SE X10 Mini is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – SonyEricsson Xperia X10 Unbrick – Boot repair supported

30.07.2011     SonyEricsson Xperia X10 Unbrick – Boot repair supported

Resurrecting SE X10 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted. Be careful, JTAG pads are covered under blue mask covering, so you will need to scratch it off in order to be able to solder wires.
During resurrection, you can select which areas to be repaired. So you can choose only those areas which you know are damaged thus saving flashing time.

To resurrect SE X10:

  •  Solder JTAG cable to SE X10 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure SE X10 is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Dopod Magic A6188 (HTC Sapp400) Unbrick, Unlock, IMEI and CID repair supported

Dopod Magic A6188 (HTC Sapp400) Unbrick, Unlock, IMEI and CID repair supported

The HTC Magic (SAPP400) is based on ESM7206A chipset. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.53.02000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘SAPP*****’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC Magic (SAPP400):

  • Solder JTAG cable to HTC Magic (SAPP400) JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Magic (SAPP400) is selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘Back (←)’ key and press ‘Power ON’ button. In few seconds you should see download mode saying Fastboot USB.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.