Tag Archives: Pc Battery

RIFF JTAG – HTC Explorer (HTC Pico) Unbrick, Unlock, SuperCID IMEI repair

Posted on by

13.07.2012  RIFF JTAG – HTC Explorer (HTC Pico) Unbrick, Unlock, SuperCID IMEI repair

 

Repairing bricked HTC Explorer is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ0310000’.

To resurrect HTC Explorer:

  •  Solder JTAG cable to HTC Explorer JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Explorer is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.

RIFF JTAG – LG E510 Optimus Hub (LG Univa) Supported

Posted on by

23.03.2012  RIFF JTAG – LG E510 Optimus Hub (LG Univa) Supported

Repairing bricked LG E510 with the RIFF Box is not very hard but it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG E510:

  •  Solder JTAG cable to LG E510 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E510 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button. In few seconds you should see emergency mode screen saying “DOWNLOAD MODE”.

.

RIFF JTAG – LG P350 Pecan / Optimus Me Unbrick – Boot Repair supported

Posted on by

12.03.2012   RIFF JTAG – LG P350 Pecan / Optimus Me Unbrick – Boot Repair supported

Resurrecting LG P350 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG P350:

  •  Solder JTAG cable to LG P350 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG P350 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods. We used KDZ_FW_UPD update software (with settings Type = 3GQCP, PhoneMode = EMERGENCY) to flash the *.KDZ firmware into phone.

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button. In few seconds you should see emergency mode screen saying “DOWNLOAD MODE”.

.

RIFF JTAG – CDMA Olive C2110 Supported

Posted on by

27.12.2011    CDMA Olive C2110 Supported

Resurrecting Olive C2110 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x2254

To resurrect Olive C2110:

  •  Solder JTAG cable to Olive C2110 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Olive C2110 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG – CDMA Samsung B339 Breeze Supported

Posted on by

23.12.2011 CDMA Samsung B339 Breeze Supported

Resurrecting Samsung B339 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x2256

To resurrect Samsung B339:

  •  Solder JTAG cable to Samsung B339 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung B339 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG – CDMA Huawei C3500 Supported

Posted on by

23.12.2011    CDMA Huawei C3500 Supported 

Resurrecting Huawei C3500 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Huawei C3500:

  •  Solder JTAG cable to Huawei C3500 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Huawei C3500 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG – CDMA Huawei C2856 Supported

Posted on by

22.11.2011  CDMA Huawei C2856 Supported

Resurrecting Huawei C2856 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0020/0x88C0

To resurrect Huawei C2856:

  •  Solder JTAG cable to Huawei C2856 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Huawei C2856 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG – CDMA Haier C301R supported

Posted on by

20.12.2011   CDMA Haier C301R supported

Resurrecting Haier C301R is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Haier C301R:

  •  Solder JTAG cable to Haier C301R JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Haier C301R is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

RIFF JTAG – HTC Desire CDMA Supported

Posted on by

24.10.2011  HTC Desire CDMA Supported

Resurrecting HTC Desire CDMA is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.60.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PP9940000’.
Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC Desire CDMA:

  •  Solder JTAG cable to HTC Desire CDMA JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire CDMA is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Back’ key and press ‘Power ON’ button.

RIFF JTAG – HTC Supersonic (EVO 4G) Unbrick, Unlock, IMEI, CID, ModelID repair supported

Posted on by

24.10.2011   HTC Supersonic (EVO 4G) Unbrick, Unlock, IMEI, CID, ModelID repair supported

Resurrecting HTC Supersonic (EVO 4G) is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.16.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC3610000’.
Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code. If selected, then ClockworkMod Recovery v5.0.2.2 will be flashed. Using this recovery you will be able to install zip files from the SD Card, for example you will be able to acquire ROOT rights by installing su-2.3.6.3-efgh-signed.zip file.

To resurrect HTC Supersonic:

  •  Solder JTAG cable to HTC Supersonic JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Supersonic is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.