Tag Archives: Pc Battery

RIFF JTAG – HTC HD Mini T5555 (HTC Photon) Unbrick, Unlock, IMEI, CID repair supported

Posted on by

29.11.2012 RIFF JTAG – HTC HD Mini T5555 (HTC Photon) Unbrick, Unlock, IMEI, CID repair supported

Repairing bricked HTC HD Mini is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB9210000’.
Currently supported resurrection for NAND memories with 2KB page size.

To resurrect HTC HD Mini:

  •  Solder JTAG cable to HTC HD Mini JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC HD Mini is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC One S Z560E (HTC Ville C) Unbrick – Dead Boot Repair Supported

Posted on by

21.11.2012  RIFF JTAG – HTC One S Z560E (HTC Ville C) Unbrick – Dead Boot Repair Supported

Repairing bricked HTC OneS is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.09.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ4020000’.

To resurrect HTC OneS:

  •  Solder JTAG cable to HTC OneS JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneS is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Samsung Gravity 3 SGH-T479 Unbrick – Dead Boot Repair Supported

Posted on by

20.11.2012  RIFF JTAG – Samsung Gravity 3 SGH-T479 Unbrick – Dead Boot Repair Supported

The Samsung T479 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Samsung T479:

  •  Solder JTAG cable to Samsung T479 JTAG pads;
  •  Connect USB cable;
  •  Make sure Samsung T479 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button.

.

RIFF JTAG – HTC EVO 4G LTE (HTC Jewel) Unbrick – Dead Boot Repair Supported

Posted on by

16.11.2012    RIFF JTAG – HTC EVO 4G LTE  Unbrick – Dead Boot Repair Supported

Repairing bricked HTC Jewel is easy with the RIFF Box.
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.15.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ7510000’.

To resurrect HTC Jewel:

  •  Solder JTAG cable to HTC Jewel JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Jewel is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – LG E610/E612 Optimus L5 Unbrick -Dead Boot Repair Supported

Posted on by

16.11.2012   RIFF JTAG – LG E610/E612 Optimus L5 Unbrick -Dead Boot Repair Supported

Repairing bricked LG E612 is easy with the RIFF Box. 
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG E612:

  •  Solder JTAG cable to LG E612 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E612 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Wildfire S CDMA (HTC Marvel C) Unbrick – Dead Boot Repair and full Support

Posted on by

13.11.2012 RIFF JTAG – HTC Wildfire S CDMA (HTC Marvel C) Unbrick – Dead Boot Repair and full Support

Resurrecting HTC WildFireS CDMA is easy with RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 (for NAND chips with 4Kb page size). Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG7620000’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC WildFireS CDMA:

  •  Solder JTAG cable to HTC WildFireS CDMA JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC WildFireS CDMA is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.

.

RIFF JTAG – Alcatel OT990 Unbrick – Dead Boot Repair Supported

Posted on by

02.11.2012  RIFF JTAG – Alcatel OT990 Unbrick – Dead Boot Repair Supported

Repairing bricked Alcatel OT990 is easy with the RIFF Box. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; moreover, if you’ll get connection errors, battery is not recommended at all.

To resurrect Alcatel OT990:

  •  Solder JTAG cable to Alcatel OT990 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Alcatel OT990 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

.

RIFF JTAG – T-Mobile myTouch2 3G Slide (HTC Espresso) Unbrick /Unlock/ Repair Boot, IMEI, CID supported

Posted on by

16.10.2012   RIFF JTAG – T-Mobile myTouch2 3G Slide (HTC Espresso) Unbrick /Unlock/ Repair Boot, IMEI, CID supported

Repairing bricked HTC Espresso is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.02.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB6510000’.

To resurrect HTC Espresso:

  •  Solder JTAG cable to HTC Espresso JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Espresso is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC ChaCha A810e Unbrick, IMEI, SuperCID and Simlock repair supported

Posted on by

05.10.2012    RIFF JTAG – HTC ChaCha A810e  Unbrick, IMEI, SuperCID and Simlock repair supported

Repairing bricked HTC ChaCha is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.04.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PH06*****’.

To resurrect HTC ChaCha:

  •  Solder JTAG cable to HTC ChaCha JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC ChaCha is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Samsung SGH-A887 Unbrick – Dead boot repair

Posted on by

10.09.2012   RIFF JTAG – Samsung SGH-A887 Unbrick – Dead boot repair

The Samsung A887 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Samsung A887:

  •  Solder JTAG cable to Samsung A887 JTAG pads;
  •  connect USB cable;
  •  Make sure Samsung A887 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Camera’ keys and press ‘Power ON’ button.

.