Tag Archives: Samsung Usb

RIFF JTAG – Samsung GT-S7500 Galaxy Ace Plus Unbrick – Boot Repair supported, World First ! ! !

Posted on by

28.02.2012      Samsung GT-S7500 Galaxy Ace Plus Unbrick – Boot Repair supported, World First !  !  !

Resurrecting Samsung S7500 is easy.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7500:

  •  Solder JTAG cable to Samsung S7500 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7500 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Samsung SGH-i777 Galaxy S II Unbrick – Boot Repair supported, World First ! ! !

Posted on by

28.02.2012    Samsung SGH-i777 Galaxy S II Unbrick – Boot Repair supported, World First !  ! !

Samsung I777 is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I777:

  •  Solder JTAG cable to Samsung I777 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I777 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Samsung GT-P6800 Galaxy Tab 7.7 Unbrick – Boot repair supported, World First !

Posted on by

27.02.2012    Samsung GT-P6800 Galaxy Tab 7.7 Unbrick – Boot repair supported, World First !

Samsung P6800 is based on the Exynos Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
To resurrect Samsung P6800:

  •  Solder JTAG cable to Samsung P6800 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung P6800 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Samsung SGH-T759 Exhibit 4G Unbrick – Boot Repair supported

Posted on by

10.01.2012     Samsung SGH-T759 Exhibit 4G Unbrick – Boot Repair supported

Samsung T759 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in some cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung T759:

  •  Solder JTAG cable to Samsung T759 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Attach battery connector;
  •  Make sure Samsung T759 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

_

RIFF JTAG – Samsung GT-i9103 Galaxy Z / Galaxy R Boot repair / Unbrick

Posted on by

31.12.2011   A new Year gift ! Samsung GT-i9103 Galaxy Z / Galaxy R (TEGRA2)  Boot repair / Unbrick

Resurrecting Samsung I9103 is easy.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inside; sometimes pressing Power On key during connection may be required. External power supply can be used too.
During some definite startup time (1…3 seconds) TEGRA2 chipsets are not detected via JTAG interface (this could be due to FUSE-d security): that is, on contrary to other devices, which being fused are detected via JTAG but non-haltable, TEGRA2 chipsets give ‘Nothing Detected’ response (though TCK-RTCK pair keeps functioning ok).
Please note: If during resurrection of dead unit the JTAG connection cannot be established (nothing is detected) then re-try with the NRST wire disconnected.

To resurrect Samsung I9103:

  •  Solder JTAG cable to Samsung I9103 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung I9103 is selected in the list of models;
  •  Click Resurrect button;
  •  If nothing is detected then try with NRST wire disconnected;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
_

RIFF JTAG – Samsung Galaxy Note (GT-i9220) Unbrick – Boot Repair Supported

Posted on by

29.12.2011      Samsung Galaxy Note (GT-i9220) Unbrick – Boot Repair Supported

Samsung I9220 AP (PDA Part) is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I9220 AP:

  •  Solder JTAG cable to Samsung I9220 AP JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9220 AP is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

_

RIFF JTAG – Samsung Galaxy Note (GT-N7000) Unbrick – Dead Boot Repair supported

Posted on by

28.12.2011    Samsung Galaxy Note (GT-N7000) Unbrick – Dead Boot Repair supported

Samsung N7000 AP (PDA Part) is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung N7000 AP:

  •  Solder JTAG cable to Samsung N7000 AP JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung N7000 AP is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

_

RIFF JTAG – CDMA Samsung B339 Breeze Supported

Posted on by

23.12.2011 CDMA Samsung B339 Breeze Supported

Resurrecting Samsung B339 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x2256

To resurrect Samsung B339:

  •  Solder JTAG cable to Samsung B339 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung B339 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG -Samsung Galaxy II, OMAP4430 version supported (Samsung i9100G, Samsung i9108)

Posted on by

07.10.2011    Samsung Galaxy II, OMAP4430 version supported (Samsung i9100G, Samsung i9108)

Samsung I9108 is based on the OMAP4430 Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface. There is a big variety of versions of Galaxy II devices: GT-I9100, GT-I9100G, GT-I9100L, GT-I9100M, GT-I9100T, GT-I9101, GT-I9103, GT-I9108, GT-I9188, and maybe more. Some of them are based on different hardware platform – the Samsung S5PV310 (Cortex-A9 Dual-Core). Thus make sure first which exact hardware version you have on hands.

Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
Current DLL is still a beta one. It will work only with phones which have killed X-Loader.

To resurrect Samsung I9108:

  •  Solder JTAG cable to Samsung I9108 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9108 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

RIFF JTAG -CDMA Samsung F619 supported

Posted on by

07.10.2011    CDMA Samsung F619 supported

The Samsung F619 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Samsung F619:

  •  Solder JTAG cable to Samsung F619 JTAG pads;
  •  Connect USB cable;
  •  Make sure Samsung F619 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘9’ key and press ‘Power ON’ button.