RIFF JTAG – Huawei modem U173-u2 Unbrick – dead boot repair supported

31.09.2013  RIFF JTAG – Huawei modem U173-u2 Unbrick – dead boot repair supported

Resurrecting Huawei E173U2 is simple. Just make sure you solder all JTAG signals and insert modem into a USB port for it to get powered.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.

To resurrect Huawei E173U2:

  •  Solder JTAG cable to Huawei E173U2 JTAG pads;
  •  Insert Huawei E173U2 modem into any USB port for power;
  •  Make sure Huawei E173U2 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

.
modem-hsdpa-huawei-e173-2_0_b

RIFF JTAG – ZTE AC30 USB modem unbrick – dead boot repair supported

15.03.2013 RIFF JTAG – ZTE AC30 USB modem unbrick – dead boot repair supported

Repairing bricked ZTE AC30 is easy with the RIFF Box.

To resurrect ZTE AC30:

  •  Solder JTAG cable to ZTE AC30 JTAG pads;
  •  Insert ZTE AC30 modem into any USB port for power;
  •  Make sure ZTE AC30 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

.
ZTE_AC30_Mifi_EVDO_Modem

RIFF JTAG – LG P999 G2X (LG Star) Modem unbrick/repair supported

19.11.2011  LG P999 G2X (LG Star) Modem unbrick/repair supported

Resurrecting LG P999 Modem part is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC while battery is inside; sometimes during connection pressing Power On key may be required.

To resurrect LG P999 Modem Part:

  •  Solder JTAG cable to LG P999 Modem JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG P999 Modem is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

 

RIFF JTAG – CDMA Pantech UM150 USB Modem supported

30.08.2011    CDMA Pantech UM150 USB Modem supported

Resurrecting CDMA USB Modem Pantech UM150 is simple. Just make sure you solder all JTAG signals and insert modem into a USB port for it to get powered.
You can select which areas to be repaired during requrrection process.

To resurrect Pantech UM150:

  •  Solder JTAG cable to Pantech UM150 JTAG pads;
  •  Insert Pantech UM150 into any USB port for power;
  •  Make sure USB Modem UM150 is selected in the list of models;
  •  Click Resurrect button;
  •  Select areas to be repaired in the settings window;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG -Sierra Wireless 597 AirCard – Unbrick – Boot repair supported

30.08.2011  Sierra Wireless 597 AirCard – Unbrick – Boot repair supported

Resurrecting CDMA USB Modem Sierra 597 is simple. Just make sure you solder all JTAG signals and insert modem into a USB port for it to get powered.
You can select which areas to be repaired during requrrection process.

To resurrect CDMA USB Modem Sierra 597:

  •  Solder JTAG cable to Sierra 597 JTAG pads;
  •  Insert Sierra 597 into any USB port for power;
  •  Make sure USB Modem 597 is selected in the list of models;
  •  Click Resurrect button;
  •  Select areas to be repaired in the settings window;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Sierra Wireless U595 USB Modem, Unbrick – Boot repair supported

30.08.2011  Sierra Wireless U595 USB Modem, Unbrick – Boot repair supported

Resurrecting CDMA USB Modem Sierra U595 is simple. Just make sure you solder all JTAG signals and insert modem into a USB port for it to get powered.
Please note, there is back cover detecting micro-switch present on the board: without back cover modem will not receive power. Thus, either asemble modem with soldered wires and attach back cover or hold micro-switch manually during all resurrection process.
You can select which areas to be repaired during requrrection process.

To resurrect CDMA USB Modem Sierra U595:

  •  Solder JTAG cable to Sierra U595 JTAG pads;
  •  Insert Sierra U595 into any USB port for power;
  •  Make sure USB Modem U595 is selected in the list of models;
  •  Click Resurrect button;
  •  Select areas to be repaired in the settings window;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Huawei E5830 Broadband modem Unbrick – Boot repair supported

12.05.2011  Huawei E5830 Broadband modem Unbrick – Boot repair supported

Resurrecting Huawei E5830 is simple. Just make sure you solder all JTAG signals. Connection can be established with USB Cable connected, though in some rare cases battery presence may be required.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
Please note, if only an USB cable is connected the device is detected by PC as unknown device. So, after resurrection in order to check if modem is alive make sure battery is connected.

To resurrect Huawei E5830:

  • Solder JTAG cable to Huawei E5830 JTAG pads;
  • Insert Huawei E5830 modem into any USB port for power;
  • Make sure Huawei E5830 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

 

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

 

RIFF JTAG – CDMA LG VM265, CDMA Huawei Broadband Modem EC1260 supported

10.05.2011  CDMA LG VM265, CDMA Huawei Broadband Modem EC1260 supported

Resurrecting LG VM265 is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG VM265:

  • Solder JTAG cable to LG VM265 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure LG VM265 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

 

 

Resurrecting Huawei EC1260 is simple. Just make sure you solder all JTAG signals and insert modem into a USB port for it to get powered.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
At resurrection startup you can select which zones are to be re-flashed. Thus you can save a lot of time if you know approximately which zone is damaged. Select EFS or MMC areas to be flashed only in case you are sure those are damaged – these areas quite big in size; unnecessary reflash is just a waste of time.
Please note, if you chose EFS to be repaired, an original ESN will be lost and substituted with the one contained in resurrection data. Current resurrector does not support ESN repair.

To resurrect Huawei EC1260:

  • Solder JTAG cable to Huawei EC1260 JTAG pads;
  • Insert Huawei EC1260 modem into any USB port for power;
  • Make sure Huawei EC1260 is selected in the list of models;
  • Click Resurrect button;
  • After Selection Dialog popup choose zones to be flashed;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

 

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Huawei E153U Broadband modem unbrick – dead boot repair supported

17.03.2011  Huawei E153U Broadband modem unbrick – dead boot repair supported

Resurrecting Huawei E153U is simple. Just make sure you solder all JTAG signals and insert modem into a USB port for it to get powered.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
There are secured (QCSBL is signed) and non-secured (QCSBL is not signed) modem revisions exist. Resurrector will automatically detect board revision and will select proper data to be flashed.
No matter what h/w revision is you can select which partitions are to be flashed during resurrection process.

To resurrect Huawei E153U:

  • Solder JTAG cable to Huawei E153U JTAG pads;
  • Insert Huawei E153U modem into any USB port for power;
  • Make sure Huawei E153U is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.